联系我们

周一至周五,8:00至17:00,我们很乐意为您提供服务。点击该链接查找您所在地区的联系人。

总部沃尔富特(Wolfurt)
+43 5574 6706-0

您的联系方式

购物车 {{ (warenkorbCtrl.warenkorb.bestellNummer ? (' [' + warenkorbCtrl.warenkorb.bestellNummer + '] ') : '' )}} | {{warenkorbCtrl.warenkorb.items.length}} 物料   更换购物篮

备注

图片 物料 件数 单价 总价 总价,含折扣
{{warenkorbItem.produktgruppe.produktname}}

{{warenkorbItem.bezeichnung | artikelBezFilter:warenkorbItem.attributwertEingaben:[{attrPrefix: 'L_', searchPattern: '/...', replacePrefix: '/', replaceSuffix: ''}] }} {{warenkorbItem.bezeichnung | artikelBezFilter:warenkorbItem.attributwertEingaben}}

{{attributwertEingabe.attributBezeichnung}}

     
{{hannexItem.Benennung}}

{{hannexItem.Bezeichnung}}

     

请登录,以便继续订购流程。

The expert for additional heat input in the mould

Do you need a fast solution for precise heat input in the mould? Not a problem with our E 6800 cartridge heater. The perfectly matched heating power and the precisely ground diameter create the best conditions for a long service life.

Components

E 6800 Cartridge heater

Quick and targeted heating for your application.

Our stainless steel cartridge heaters offer the best combination of characteristics for optimum heat conduction, high corrosion resistance and appropriate thermal expansion. The precisely ground outer diameters ensure perfect installation in the appropriate hole depending on the surface load. In addition, the high-precision ground surface allows optimum heat dissipation to the mould which increases service life as well as efficiency.

Applications

  • For increasing flow line strength
  • For heating thermosetting plastics and elastomer moulds
  • Mould heating for variotherme process
  • Other applications where high heating power is required

To the product

Installation

Cartridge heaters with a surface load of up to 20 W/cm² require a H7 hole.

Cartridge heaters which have a higher surface load need to have a press fit to ensure good heat dissipation from the cartridge heater and thus a long service life.

A reamer is most suitable to produce the hole.

If several cartridge heaters are installed, they must have a minimum space of one time the diameter of the cartridge heater. We recommend using a solid-based high-temperature lubricant (VAP 1000) for installation.

Important!
Do not use conductive sprays or pastes near the connection area.

Removal

For the easiest possible removal, we recommend an offset hole which is 0.2 to 0.3 mm smaller than the cartridge heater diameter.

To avoid damaging the cartridge heater during removal, use a tube or pin with a slightly smaller diameter of the hole to prevent the cartridge heater from slipping through the hole. That way, the forces needed for the removal are concentrated on the reinforced area of the cartridge heater.

If a through hole for removal is not possible, the use of 2 plates, each with half of the hole, is a good alternative.

Position of the thermocouple

For good process control and to ensure that the required temperature is reached, the thermocouple should be positioned close to the object to be heated. In addition, to protect the cartridge heater from overheating and ensure a long service life, the thermocouple is ideally mounted 10 mm away from the cartridge heater.

Often a compromise is necessary between these two requirements, which is usually made by averaging out the space and not using full power, and helps to ensure a long cartridge heater service life.

Calculation

For information on finding the right cartridge heater and quantity as well as calculation examples and other useful information, please refer to our fact sheet.

To the calculation example



Operating the cartridge heater

Our profiTEMP+ device provides the ideal solution for monitoring and controlling the cartridge heaters with maximum process safety and reliable temperature control using state-of-the-art hardware and software components.

Connection scheme

A start-up circuit at the beginning of the process allows moisture to escape gently from the cartridge heaters, thus ruling out short circuit failures.

To the profiTEMP+

登录

您已是客户?

若您已拥有Meusburger门户的访问数据,请在此登录:

忘记密码了?

新密码已生成,并将很快被发送至您的收件箱。我们祝您有顺利的一天。

请在下方输入您的邮件地址。
我们会将新密码发送给您。

选择您的国家

位置

Try our new version of 'My account'

Get familiar with our new ‘My account’ section and benefit from numerous advantages.

Now the new ‘My account’ also gives you a direct insight into the next level of the Meusburger portal. Check out all the information and benefits of the portal here.

Get familiar with our new ‘My account’ section and benefit from numerous advantages.

Now the new ‘My account’ also gives you a direct insight into the next level of the Meusburger portal. Check out all the information and benefits of the portal here.

Keep selection
Beta
New version
Current version